View Source: LmSensorsDellFifteenFifty

Note: This page has been locked and cannot be edited.
lm_sensors configuration for Dell 1550 systems.

Load the following modules (on ~RedHat or Fedora, add them to /etc/sysconfig/lm_sensors):

<verbatim>
i2c-piix4
adm1021
adm9240
</verbatim>

Add the following entry to /etc/modules.conf (for 2.4 kernels) or /etc/modprobe.conf (for 2.6 systems):

<verbatim>
alias char-major-89 i2c-dev
</verbatim>

And use the following /etc/sensors.conf:

<verbatim>
chip "lm81-*"

chip "max1617a-*"

label temp           "Board"
label remote_temp    "CPU Temp"
</verbatim>

Sample output:

<verbatim>
max1617a-i2c-0-18
Adapter: SMBus PIIX4 adapter at 0580
Algorithm: Non-I2C SMBus adapter
Board:       +31?C  (low =   +5?C, high =  +55?C)
CPU Temp:    +25?C  (low =   +5?C, high =  +75?C)

lm81-i2c-0-2c
Adapter: SMBus PIIX4 adapter at 0580
Algorithm: Non-I2C SMBus adapter
2.5V:      +2.46 V  (min =  +2.36 V, max =  +2.63 V)
Vccp1:     +1.70 V  (min =  +1.60 V, max =  +1.78 V)
3.3V:      +3.26 V  (min =  +3.12 V, max =  +3.47 V)
5V:        +5.00 V  (min =  +4.73 V, max =  +5.26 V)
12V:      +11.68 V  (min = +11.18 V, max = +12.62 V)
Vccp2:     +1.49 V  (min =  +1.37 V, max =  +1.60 V)
fan1:     11065 RPM  (min = 8333 RPM, div = 2)
fan2:     11250 RPM  (min = 8333 RPM, div = 2)
temp:      +25.0?C  (limit =  +55?C, hysteresis =   +5?C)
vid:       +1.70 V
alarms:

lm81-i2c-0-2d
Adapter: SMBus PIIX4 adapter at 0580
Algorithm: Non-I2C SMBus adapter
2.5V:      +0.00 V  (min =  +0.01 V, max =  +3.30 V)   ALARM
Vccp1:     +1.70 V  (min =  +1.22 V, max =  +1.36 V)   ALARM
3.3V:      +3.28 V  (min =  +1.10 V, max =  +0.03 V)   ALARM
5V:        +5.00 V  (min =  +4.73 V, max =  +5.26 V)
12V:      +11.68 V  (min =  +0.00 V, max =  +0.00 V)   ALARM
Vccp2:     +1.50 V  (min =  +0.00 V, max =  +0.00 V)   ALARM
fan1:     11637 RPM  (min = 8333 RPM, div = 2)
fan2:     11440 RPM  (min = 8333 RPM, div = 2)
temp:      +25.0?C  (limit =  +55?C, hysteresis =   +5?C)
vid:       +1.30 V
alarms:

lm81-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0580
Algorithm: Non-I2C SMBus adapter
2.5V:      +2.36 V  (min =  +1.49 V, max =  +2.63 V)
Vccp1:     +0.00 V  (min =  +0.22 V, max =  +0.45 V)   ALARM
3.3V:      +3.26 V  (min =  +3.12 V, max =  +3.47 V)
5V:        +5.02 V  (min =  +4.73 V, max =  +5.26 V)
12V:      +11.75 V  (min = +11.18 V, max = +12.62 V)
Vccp2:     +0.00 V  (min =  +1.85 V, max =  +0.25 V)   ALARM
fan1:     8231 RPM  (min = 7258 RPM, div = 2)
fan2:        0 RPM  (min =    0 RPM, div = 2)
temp:      +24.0?C  (limit =  +55?C, hysteresis =   +5?C)
vid:       +2.05 V
alarms:
</verbatim>

Note that this could be improved a lot with use of ''ignore'' and ''set'' min/max lines.

-----

CategoryGeekStuff
View Source: LmSensorsDellFifteenFifty

Main Categories

Search

Toolbox

RecentChanges

Favorite Categories

Views
